If you want to replace your original router which connects to the internet with a PPoE and password, start from step 1. Otherwise, start from step 2.
Step 1: Migrate your PPoE user name and password from your original router
- Power on your original and new router
- Connect the WAN port of the original router to port 1, 2 or 3/IPTV of the new router using an Ethernet cable
- Wait about 5 seconds (when the WAN,1,2 and 3 indicators of the new router turn solid on after blinking fast, your migration is successful)
- Remove the original router
Step 2: Connect to the internet
- Power off your modem, and remove its battery (if any)
- Connect the WAN port of the new router to the LAN port to your Ethernet jack
- Reinstall your modem's battery. Power on your modem and the new router
- Connect your wireless devices to the WiFi network of the router.
- The default SSID (WiFi name) and password are labeled on the bottom/front of the router.
- Connect your wired devices to port 1,2 or 3/IPTV of the router using Ethernet cables. The corresponding indicators light will come on
Follow the following steps to set up your router:
- Start a web browser on a device that has connected to the router. Enter 192.168.01 in the address bar, and press Enter.
- Click Start.
- Confirm or set the related parameters. Then click Next.
- Set your WiFi name (SSID), WiFi password and login password. Then click Next. Please note: the WiFi password is used to connect to the WiFi network of the router, and the login password is used to log in to the web UI of the router.
- Reconnect your wireless devices tot he router's WiFi network using the WiFi names and the WiFi password you set. Ther wired devices can access the intent directly if they have connected to port 1, 2 or 3/IPTV
Try the following solutions and log in again:
- Ensure that your Ethernet cable with internet connectivity is plugged into the WAN port of the router rather than a LAN port.
- Ensure that your wireless device is connected tot he router's SSID.
- Ensure that your wired devices is connected to port 1, 2 or 3/IPTV of the router properly by Ethernet cable. And the device is also set to Obtain an IP address automatically and obtain DNS server address automatically.
- Ensure that 192.168.0.1 is entered correctly.
- Replace the web browser and log in again.
- Reset the router and log in again.
Log in to the web UI of the router,and check your router's connection status on the internet status page.
If your router is connected tot he internet successfully:
- Connect your wireless devices to the WiFi network of the router using the new WiFi name and password.
If the connection failed appears on the page:
- Click Internet settings on the web UI to check whether the connection type and parameters you entered are correct
- Connect the Ethernet cable with internet connectivity to your computer directly.
If your computer cannot access the internet, consult your ISP. Otherwides, reconnect the Ethernet cable with internet connectivity to yopur router, reset your router and condigure it again.
Please ensure you have verified your connection setup with your ISP before installing this router. Some setups will use combination routers that have both modem and router functions. The Ultra-link WF1200 router does NOT include a built-in modem function. To connect the Ultra-link WF1200 router and utilise your Internet from your ISP you will need a standalone modem device to convert the data from your ISP, most ISP’s will supply this device upon installation. The Ultra-link WF1200 must be connected via LAN cable to the standalone modem device and not directly to your ISP line. To support ADSL, you will need an ADSL modem. To support Fibre, you will need a Fibre modem. To support 4G you will need a 4G modem or 4G mobile router as all these networks use different modems.
With the Ultra-Link Android TV Box, you have two options with internet connection: WiFi & Ethernet.
Open “settings” – “network”, click on the WiFi source you want to connect to after the connection is successful, you can access the internet
Connect the Ethernet cable to the product. The Ultra-Link TV Box will automatically connect
Open “settings” – “APPS”, select the APK you want to uninstall, press OK, click Uninstall.
You can try the following to solve this problem:
- Aim the remote control directly at the sensor on the front of the TV Box
- Reduce the distance to the TV Box
- Replace the Batteries in the remote control
- The audio codec may not be supported by the TV Box.
- You can change the supported audio on playing menu
- Check the volume
For optimum performance, place your device:
- Near the center of the area where your computers, smartphones and other devices operate, and preferably within line of sight to your wireless devices
- In an elevated location such as a high self, keeping the number of walls and ceilings to a minimum between the router and other clients such as computers and smartphones
- Away from electrical devices that are potential sources of interference such as ceiling fans, home security systems or microwaves
- Away from any large metal surfaces, such as solid metal door or aluminum studs
- Away from other materials such as glass, insulated walls, fish tanks, mirrors, brick and concrete that can also affect your wireless signal
Please do as the following one by one until you solve your problem:
- Verify the Ethernet cable between your PC and the router is intact and well-connected. If not, replace Ethernet cable.
- Clear cache of your browser, or change another browser
- Double-check the TCP/IP settings on your PC. Verify that it is set to obtain an IP automatically
- Press and hold the WPS/RST button for about 8 seconds and then release it to reset the router to factory default settings. Then try logging into it again
- Try accessing the web UI from another PC, smart phone or iPad
Please do as the following one by one until you solve your problem
- Log into the wireless router’s web UI, and view the WiFi password on the wireless settings page
- Restore the wireless router to factory default settings, and reset the WiFi password.
- Restore method: Press and hold the WPS/RST button for about 8 seconds and then release it
Please ensure you have verified your connection setup with your ISP before installing this router. Some setups will use combination routers that have both modem and router functions. The Ultra-link WF300 router does NOT include a built-in modem function. To connect the Ultra-link WF300 router and utilise your Internet from your ISP you will need a standalone modem device to convert the data from your ISP, most ISP’s will supply this device upon installation. The Ultra-link WF300 must be connected via LAN cable to the standalone modem device and not directly to your ISP line. To support ADSL, you will need an ADSL modem. To support Fibre, you will need a Fibre modem. To support 4G you will need a 4G modem or 4G mobile router as all these networks use different modems.
- Tap the node on the Ultra-Link WiFi App, tap in the upper-right corner, and choose Delete
- Note: Removing operation restores the node to factory settings
- Yes you can!
- Run Ultra-Link WiFi App, tap “settings” in the lower-right corner, tap UL-INT-MW3, and follow the on-screen instructions to add.
- With your nodes powered on, hold the RST button of your primary node down using a paper clip for about 6 seconds, release when the LED indicator blinks fast.
- Your network is reset successfully when the LED indicator lights solid on then blinks fast again. All nodes are now restored to factory settings
- Connect your smart phone used for setup to your Mesh Router WiFi Network
- Run Ultra-Link WiFi App, tap “settings” then “smart assistant” and enable. Your smartphone connects to the 2.4 GHz WiFi network
- Use the smartphone to set up your 2.4 GHz WiFi-enabled device guided by its App
25 June 2020:
We apologize for any inconvenience that you might have experienced. Our App is currently being updated on the Apple App store, therefore it is currently unavailable.
Please use the "MyMesh" App that is available on the Apple App Store as an alternative.
- Use your computer to connect to the WiFi name (SSID) on the label of the extender’s back panel
- Launch a web browser, type 192.168.0.254 into the address bar and tap Enter on the keyboard
- Use your computer to connect to the extended WiFi name (if you customize the WiFi name of the extender, connect that):
- Launch a web browser, type 192.168.0.254 into the address bar and tap enter on the keyboard